NADQ Series Automatic Capacitance Bridge / Inductance / Current Tester   NADQ全自動電容電橋測試儀

產品簡介

NADQ全自動電容電橋測試儀針對變電站現場測量并聯電容器組中的單個電容器電容值時存在的問題而專門研制的，它著重解決了以下問題：

（1）現場測量單個電容器需拆除連接線，不僅工作量大而且易損壞電容器。

（2）電容表輸出電壓低而導致故障檢出率低。

NADQ全自動電容電橋測試儀具有測量工作量小、快捷簡便、性能穩定、測量準確、故障檢出率高等特點。此外，它的電流測量單元還可兼作CVT、避雷器等電器設備的測量之用，具有一機多能的功效。

產品別名

電力電容測試儀，電力電容器測試儀，電容電橋，數字電容電橋測試儀，全自動電容電感測試儀，配電電網電容電橋測試儀，全自動電容測試儀，全自動電容量測試儀，全自動電容量測量儀

產品特性

（1）量程自動轉換；

（2）儲存7168個測試數據；

（3）大屏幕液晶（320×240 LCD）顯示, 漢字菜單操作提示；

（4）實現波形和測量處理數據同屏顯示，使測試過程更直觀；

（5）具有設置、校正和調試功能。

主要參數

1、電容量量程：0.2μF～2,000μF；

     容量范圍：5～20,000 kvar；

     測量精度：0.2μF～2μF ±1%讀數±0.02μF；(內置)

                2μF～2,000μF ±1%讀數±2個字；（鉗式）

2、輸出測量電壓：AC 26V/500VA；50Hz；

3、顯示方式：大屏幕液晶示屏全漢字輸出，面板式熱敏打印機

4、外形：370mm×370mm×220mm

5、重量：16 kg

6、工作條件：

    a. 環境溫度：0℃ ～ +40℃，相對濕度：≤90%

    b. 電 源：AC 220V±10%；50Hz。

Product introduction

At present, most power distribution system is generally not neutral point directly grounded , so when the line is single- phase ground fault current flowing through the actual line to ground capacitance is the capacitance current. According to statistics, the distribution network failure is largely due to line single-phase ground when the capacitor is too large to be caused by self- interest arc . Thus, when electricity Statutes 10kV and 35kV system when the capacitor current is greater than 30A and 10A, respectively , shall be equipped with arc suppression coil to compensate for capacitive current , which requires current distribution network capacitance measurements to make a decision. In addition, the distribution network to ground capacitance and the PT will generate parameter with PT error over-voltage , in order to verify that the distribution system will occur and what the nature of PT resonance resonance , it must accurately measure the distribution network for ground capacitance value. The traditional distribution network capacitive current measurement methods are single-phase l grounding direct method , plus capacitance indirect measurement method, etc. These methods have come into contact with one device , so there is danger test , operate complex , efficient and low defects . NADQ series Automatic Capacitance Bridge / Inductance / Current Tester, directly from the secondary side of the PT measuring capacitive current distribution network , compared with traditional testing methods , NADQ series Automatic Capacitance Bridge / Inductance / Current Tester and one side without dealing with , which is not there is the risk of trial , without doing complicated security measures and wait for lengthy scheduling order , simply measuring line connected to the open delta PT clients can measure the capacitive current data . Triangular openings due from the PT was injected at different frequency test signal weak , so neither will relay protection and PT itself, have any impact , but also to avoid the 50Hz power frequency interference signals, while the output of the tester can be resistant to by 100V AC voltage , if the measurement system is single-phase ground fault occurs , will not damage the PT and tester, eliminating the need to make special security measures to make this work to become safe, simple , fast, and accurate test results , stable and reliable.

Also called name

capacitance current tester, automatic capacitance current tester, capacitance current tester for distribution network

The Characteristics of the products

NADQ Automatic Capacitance Bridge Tester

Products Characteristics

(1) automatic conversion range;

(2) test data storage 7168;

(3) Large LCD (320 × 240 LCD) display, English menu operation s;

(4) the realization of waveform and measurement data processing with the screen display, making the testing process more intuitive;

(5) has set up, calibration and debugging features.